{"id":14070,"date":"2019-03-26T10:29:24","date_gmt":"2019-03-26T10:29:24","guid":{"rendered":"https:\/\/uaetechnician.ae\/?p=14070"},"modified":"2019-10-08T07:48:17","modified_gmt":"2019-10-08T07:48:17","slug":"configure-multiple-hard-drives-together","status":"publish","type":"post","link":"https:\/\/uaetechnician.ae\/configure-multiple-hard-drives-together","title":{"rendered":"Configure Multiple Hard Drives Together"},"content":{"rendered":"
<\/p>\n
Learn All About RAID Setups and RAID Data Recovery<\/strong><\/h2>\n
RAID (redundant array of inexpensive disks) allows users to configure multiple physical hard drives into one single logical drive. RAID holds two major benefits. It increases the performance, and also provides protection against data loss from drive failure. RAIDs used to be expensive and the only ones who could afford it was software companies with dedicated IT departments. But now, things have changed. Nowadays, most desktops run on motherboards that support RAID. Windows 7 even provides users with a dedicated software which does not need a special hardware at all. Thus, RAID is now within the reach of common users. All you need is the right knowledge about RAID, and you are all set to use it for maximum benefits including RAID data recovery.<\/b><\/p>\n
RAID Modes and how to Use Them<\/h2>\n
Setting up RAID in most cases is as easy as installing some drivers, attaching them to a RAID controller, and following a wizard. However, the main factor is to decide which RAID mode you want to use. Each of the RAID modes such as RAID 0, or RAID 5, offers different functionality and differs in the way they work. They also offer different security levels. The different RAID modes are discussed below:<\/p>\n
RAID 0: Striping<\/h3>\n
This setup splits or stripes data across two or more drives and thus increases the hard drive performance. For example, if you write a 200 MB file across this RAID 0 setup, and you have two physical hard drives, then 100 MB of the file would be written on one drive and the remaining 100 MB on the other. When the computer needs to read that file, it would again read half from one drive, and the other half from the other drive. This process is significantly faster than reading a 200 MB file from a single drive. However, the chances of data loss are also significantly more in this RAID 0 setup. This is because, if one of the multiple drives fails, then the whole data, divided between drives, is also lost. RAID 0 setup is prevalent in high-end gaming PCs, and also graphic design workstations.<\/p>\n
RAID 1 (Mirroring)<\/h3>\n
This setup reads and writes data to pairs of drives, which is often referred to as mirroring. In a RAID 1 setup, the computer writes the same data to each of the two drives, so that should any one of them fail, you can continue your work through the other one. So, if you set up two 1TB hard drives in RAID 1 setup, it offers you a viable 1TB of usable space, not 2TB. You can have as many pairs of mirrored drives as you wish, provided your RAID controller allows to have them. Thus, with a RAID 1 setup, you have a greater speed and higher chances of RAID data recovery<\/b>. However, the usable hard disk space is reduced to half.<\/p>\n
RAID 5 (Distributed Parity)<\/h3>\n
RAID 5 uses a minimum of three physical disks. This setup writes and reads from all the three drives equally. The redundancy or parity information is also stored equally among the three drives. Parity information or parity data is a smaller amount of data which is derived from a larger amount of data, and which can accurately describe the larger data. It is because of this parity information, that if one of the hard drives in a RAID 5 setup fails, you have a chance of recovering most of the data through RAID data recovery<\/b><\/a>, because of the parity information stored in the two other drives.<\/p>\n